| DYNO PROVEN TO PROVIDE THE LARGEST HORSEPOWER GAINS FOR THE 05-08 MUSTANG GT
|
|
| STRATEGY
In keeping with our goal of providing our customers with the best possible value, we have tested a large group of components specifically designed for the 05-08 Mustang GT 3 Valve Motor.
We have invested hundreds of hours evaluating and refining each of the new 4.6L 3V products on our MD Chassis DYNO, and at race tracks coast to coast to ensure that we would develop as much power as possible, and as safely as possible.
The site menu on the left side of this page, lists the clear winners when it comes to “performance vs. dollar” value. Please check back often as we are always testing and developing new ways to create more horsepower.
(shown on right)
746 RWHP (823 crankshaft HP) 2005 3V Mustang GT
Stock Motor, DiabloSport Tuned F-1A ProCharger Kit! |
|
|
CANTON ALUMINUM COOLANT EXPANSION - POWER STEERING TANK
05-08 MUSTANG GT/SHELBY GT500
We are proud to announce the introduction of the newest addition to our Mustang parts accessories selection.
RPM Outlet now offers Canton Racing Products Aluminum Coolant Expansion tank, and Power steering Tank.
|
|
COOLANT EXPANSION/FILL TANK
05-08 Mustang / Mustang GT/ Shelby GT500
This aluminum Mustang coolant tank is a direct bolt-in replacement for 05-08 Mustang/Mustang GT/ Shelby GT500. Tank features 1/4" billet bottom inlet fitting. Exclusive Billet factory stock vented cap, bleeds pressure like the factory intended.
- Direct bolt-in replacement for plastic tank
- Fabricated Aluminum for strength
- Uses factory stock vented cap
- Integral billet aluminum fittings
Part# MOR63768 $ 139.99
Click-On Price to Order
|
|
FORD POWER STEERING RESERVOIR TANK
Fits all listed applications below
This lightweight aluminum is a direct bolt-in replacement for '05-08 V-8 Mustang's. Offers increased strength over the factory plastic tank.
Baffled for proper fluid control and comes with the neccassary bracket, fittings and top for a direct bolt-in fit.
Tank can be polished for a high shine or anodized for a personal touch.
- Mustang GT '05-'08
- Shelby GT500 '07-'08
Part# MOR63491 $ 99.99
Click-On Price to Order
Installation of this tank is quite simple includes all of the special parts needed and should take no more than ½ hour to complete.
|
Installation of this tank is quite simple includes all of the special parts needed and should take no more than ½ hour to complete.
|
05-08 Mustangs
Stainless Steel Radiator Cover
The MOTOBLUE brushed finish stainless steel radiator cover upgrades the appearance under hood.
Installation of this kit is quite simple includes a tube of silicon for a simple, tool-free 10 minuets install.
- Mustang GT 05-08
- Mustang V6 05-08
- CNC laser cut tooling
- Brushed stainless steel finish
05-09 Mustang Part#MTB-420001 $ 79.99
07-08 Mustang Part#MTB-420002 $ 79.99
|
(hairpin-style clip shown in this image) |
Ford Mustangs
Authentic Hood Pin Kits
Authentic Hood Pins. These Hood Pins are real thing; they do require drilling into your hood.
Not just a simple second rate type that adheres to your hood using the 3M bonding tape or that is made from cheap Zinc Die Cast, and Chrome Plated.
This kit is competition-proven for quick opening of hood and has
show-type eye appeal. Stainless steel scuff plates and long lanyard
cables make a super kit that installs easily
Best yet they work on every Mustang; early, late, and any model.
- Mustang; early, late, and any model
- Long lanyard stainless cables
- Stainless steel scuff plates
- CNC laser cut tooling
Origional Hairpin-Style Clip 4 in. Long #MRG-1616 $ 19.99
Competition Torsion Clip Style 4 in. Long #MRG-1607 $ 19.99
Simple 1/2 hour install with basic hand tools
|
(Simple adhere/clip-on plates no drilling no cutting) |
Authentic 07-08 GT500 SVT SILL PLATES
If you have a 2005+ Mustang and it has doors, then you need a set of these Aluminum Mustang GT500 SVT Still Plates! Cover up that dingy Ford plastic still plates with Authentic 07-08
GT500 aluminum still plates giving your car mad open door appeal!
Best yet they work on every 05-08 Mustang; v6 or v8 models.
- Fits 2005-08 Mustangs
- Improves appearance and protects vehicle entry area
- Black with brushed stainless steel insert with “SVT” logo
- Simple Adhere/Clip-on Plates
- Easy Install no drilling or screws
Kit includes two sill plates, installation tape and instructions
Sold is set of (2) two
Part # FMS-M-13208 $ 99.99
|
(Includes special wire harness for easy installation)
Click here to view the parts instruction sheet. |
FORD RACING MUSTANG GT START BUTTON KIT
This is the latest of the must have part for your 05-08 Mustang. The Ford Racings dash mounted remote starter button is designed to replace the existing power point located in the center of the dash.
Easy to install designed to enhance the appearance of your 2005-08 Mustang, simply turn the key to the on position then press the button, includes special wire harness for easy installation.
Best yet they work on every 05-08 Mustang; v6 or v8 models.
- Fits All 05-08 Mustangs
- Fits in the existing Power Point located in the center of the dash
- Turn the key to the on position then press the button
- Kit includes special wire harness for easy installation, and installation instructions
- Red illumination only
Part # FMS-M-11572-GT $ 105.99
|
MOTOBLUE™ LINE-LOCK SYSTEM (brake-control kit)
05-08 V8-V6 Mustang
An RPM Outlet exclusive, this unit is designed to fit all 05-08 5.4L / 4.6/5.4L/4.0L Mustangs. Here's how it works: Press the brake pedal and hold the roll control Snap-action switch down. Remove your foot from the pedal, and the solenoid maintains line pressure to the front brakes until the switch is released. This makes it easy to heat the rear tires in the burnout box, while minimizing wear and tear on your car's rear brake components. You can also use the system to prevent a manual-trans car from rolling out of the staging beams at the starting line.
|
The MOTOBLUE™ LINE-LOCK SYSTEMS is custom-fitted to the new Mustang chassis (no tweaking or fabrication required!) and is fully compatible with the factory anti-lock braking and traction-control
systems. It includes a waterproof electrical solenoid, an activation switch, plug-in wires, CNC-bent steel lines with correct OE fittings,
mounting hardware, and detailed installation instructions.
MOTOBLUE™ Kit Features:
- HURST Stainless steel solenoid.
- HURST Micro switch and 4 foot cable.
- HURST On/Off LED Light.
- FORD CNC-bent steel lines.
- Fuse and fuse assembly.
- Mounting bracket, screws
- Installation instructions.
|
Note: This kit is compatible with factory anti-lock brakes and traction control systems.
| MOTOBLUE™ Brake-Control Kit 05-09 Mustang GT/V6 |
| Part # |
Year |
Engine |
Application |
Price |
| MTB-250000 |
05-08 |
5/4L
4.6L
4.0L |
MOTOBLUE™ LINE-LOCK SYSTEMS (brake-control kit)
05-09 Mustang GT/V6 Automatic / Manual |
$ 129.99 |
Click-On Price to Order
|
| INSTALLER NOTE:
MOTOBLUE™ highly recommends hiring a professional installer, one that is familiar with the
installation of off-road performance products. MOTOBLUE™ products are designed to increase the performance
of your vehicle, and as such are designed differently than your stock system. Extra care must be taken to insure
that any interaction between this system and other systems that you have on the vehicle have been taken into account
when installing performance products. This includes but are not limited to, fit of components, rubbing leakage, possible
contact with moving parts and or contact with heat sources. |
|
Aluminum Coolant/Expansion Tank 
Line-Loc / Brake Control Kits
Stainless Steel Hood Pin Kits 
SVT Mustang Door Sill Plates
Synthetic Motor Oil / Gear Fluids 
S&B Performance Intake Kit (25+hp) 
Filters
K&N Gen. II FIPK® Kit (16+hp)
TRUEFLOW 85mm Cold-Air Kit (22+hp) 
Shelby GT500 Twin 65mm Upgrade Kit
Performance Disc Brake Kits
Stainless Steel Brake Line Kits 
PRO SERIES Performance Radiators
160º/180º LOW TEMP T/Stats
PREDATOR Tuner (27+hp) 
LIVEWIRE Flash Programmer
LAKEWOOD BFL® Racing Gear Lubes
Rear End Girdle and Stud kit 
DYNO TUNED POWER OPTIONS™
XFI™ NSR Cam/Spring Kit (30+hp)
Stage I/II/III Camshafts/Spring
Harmonic Balancer Pulley
STAGE II/III Cyl. Heads
Modular 4.6L Rotating Assemblies 
SCREEN Windage Tray (+12 hp) 
Long-Tube HEADERS / X-pipe Kits
Ceramic Long-Tube / X-pipe Kits
CERAMIC Long-Tube/Headers
SERIES X-Pipe w/wo Cats
Stainless Axle-Back™ Kit
American Thunder Axle-Back™ Kit
Stainless Emissions Legal X-Pipe 
GaugeWorks Pillars and Pods 
2 1/16 inch dia. Gauges
Wideband air/fuel with data-logger
Multi-Spark coil-on-plug
DIRECT-FIRE Modular SuperCoils
Blaster Coil-near-Plug 
BRISK 3V Modular Spark Plugs
™ Nitrous Oxide Systems (35-175 +hp)
Nitrous Oxide System (75-175 +hp)
Boost Coolers 
Street/Strip Adjustable Shock/Struts
FRONT-END Alignment Kit
TUBULAR Adjustable Panhard Kits
Drag Radials / Drag Slicks
Dual-Friction Clutch Kits
Street-Strip Clutch/Flywheel Kits 
TCI StreetFighter® Torque Converters
CNC Billet Performance Shifter 
Precision Sport Short-Throw Shifter